E2E

List of Models

Sensors

Higher Oil Resistance, DC 2-Wire, Pre-wired Models

Higher Oil Resistance, DC 2-Wire, M12 Smartclick Pre-wired Models

DC 2-Wire, Pre-wired Models (Models with self-diagnostic function are 3-wire.)

*1. Models with different frequencies are also available. The model numbers are E2E-X[]D15 (example: E2E-X3D15-N).

*2. Models with robotics cables are also available. Add "-R" to the end of the model number (example: E2E-X4MD1-R).
The model number E2E-X2D1-N, however, becomes E2E-X2D1-R.

*3. Models are also available with 5-m cables. Add the cable length to the model number (example: E2E-X3D1-N 5M).

DC 2-Wire, Connector Models (Models with self-diagnostic function are 3-wire.)

*1. Models with different frequencies are also available. The model numbers are E2E-X[]D15-M1G (example: E2E-X3D15-M1G).

*2. Refer to Datasheet.

DC 2-Wire, Pre-wired Connector Models

Appearance		Sensing distance	Operate Mode	Model
				Polarity: Yes	Applicable connector code *	Polarity: None	Applicable connector code *
	M12	3 mm	NO	E2E-X3D1-M1GJ	A	E2E-X3D1-M1J-T	B
	M18	7 mm		E2E-X7D1-M1GJ	A	E2E-X7D1-M1J-T	B
	M30	10 mm		E2E-X10D1-M1GJ	A	E2E-X10D1-M1J-T	B
	M12	8 mm		E2E-X8MD1-M1GJ	A	---	---
	M18	14 mm		E2E-X14MD1-M1GJ	A	---	---
	M30	20 mm		E2E-X20MD1-M1GJ	A	---	---

Note:
1. A model with no polarity has a residual voltage of 5 V, which must be taken into consideration together with the interface conditions (the PLC’s ON voltage, for example) when connecting the Proximity Sensor to a load. Refer to Datasheet.

2. The standard cable length is 300 mm. Models are also available with 500 mm and 1 m cables.

* Refer to Datasheet.

Connector Pin Assignments of DC 2-Wire Models

The connector pin assignments of each New E2E DC 2-Wire Model conform to IEC 947-5-2 Table III. (Only DC 2-Wire Models have been changed in comparison to the previous models.)

The following models with conventional connector pin assignments are available as well. (Only NO Models can be used.)
The cable at the right should also be used if the XW3A-P[]45-G11 Connector Junction Box is already being used.

Models with conventional connector pin assignments are available as well.

Appearance		Model
		NO	Applicable connector code *	NC	Applicable connector code *
	M8	E2E-X2D1-M1	C	E2E-X2D2-M1	D
	M12	E2E-X3D1-M1	C	E2E-X3D2-M1	D
	M18	E2E-X7D1-M1	C	E2E-X7D2-M1	D
	M30	E2E-X10D1-M1	C	E2E-X10D2-M1	D
	M8	E2E-X4MD1-M1	C	E2E-X4MD2-M1	D
	M12	E2E-X8MD1-M1	C	E2E-X8MD2-M1	D
	M18	E2E-X14MD1-M1	C	E2E-X14MD2-M1	D
	M30	E2E-X20MD1-M1	C	E2E-X20MD2-M1	D

Note: Refer to Datasheet.

DC 3-Wire, Pre-Wired Models

Appearance		Sensing distance	Model
			Output configuration: NPN NO	Output configuration: PNP NO
	3 dia.	0.6 mm	E2E-CR6C1	E2E-CR6B1
	4 dia.	0.8 mm	E2E-CR8C1 *1 *2	E2E-CR8B1 *2
	M5	1 mm	E2E-X1C1 *1 *2	E2E-X1B1 *2
	5.4 dia.	1 mm	E2E-C1C1 *1 *2	E2E-C1B1
	M8	1.5 mm	E2E-X1R5E1 *1 *2	E2E-X1R5F1 *1 *2
	M12	2 mm	E2E-X2E1 *1 *2 *3 *4	E2E-X2F1 *1 *2 *3
	M18	5 mm	E2E-X5E1 *1 *2 *3 *4	E2E-X5F1 *1 *2 *3
	M30	10 mm	E2E-X10E1 *1 *2 *3 *4	E2E-X10F1 *2
	M8	2 mm	E2E-X2ME1 *2	E2E-X2MF1 *2
	M12	5 mm	E2E-X5ME1 *1 *2 *3 *4	E2E-X5MF1 *2
	M18	10 mm	E2E-X10ME1 *1 *2 *3 *4	E2E-X10MF1 *2
	M30	18 mm	E2E-X18ME1 *1 *2 *3 *4	E2E-X18MF1 *2

Note: Models with NPN NC output configurations are also available for all of the above models.

*1. Models are also available with 5-m cables. Add the cable length to the model number (example: E2E-X2E1 5M).

*2. Models with robotics cables are also available. The model numbers are E2E-X[]E1-R (example: E2E-X5E1-R).

*3. Models with different frequencies are also available. The model numbers are E2E-X[]E[]5 (example: E2E-X5E15).

*4. These models are also available with e-CON connectors (0.3-m cable). Add "-ECON" to the end of the model number (example: E2E-X2E1-ECON).

DC 3-Wire, Connector Models

Connector	Appearance		Sensing distance	Model		Applicable connector code *
				Output configuration: NPN NO	Output configuration: PNP NO
M12		M8	1.5 mm	E2E-X1R5E1-M1	E2E-X1R5F1-M1	B
		M12	2 mm	E2E-X2E1-M1	E2E-X2F1-M1	B
		M18	5 mm	E2E-X5E1-M1	E2E-X5F1-M1	B
		M30	10 mm	E2E-X10E1-M1	E2E-X10F1-M1	B
		M8	2 mm	E2E-X2ME1-M1	E2E-X2MF1-M1	B
		M12	5 mm	E2E-X5ME1-M1	E2E-X5MF1-M1	B
		M18	10 mm	E2E-X10ME1-M1	E2E-X10MF1-M1	B
		M30	18 mm	E2E-X18ME1-M1	E2E-X18MF1-M1	B
M8		M8	1.5 mm	E2E-X1R5E1-M3	E2E-X1R5F1-M3	G
			2 mm	E2E-X2ME1-M3	E2E-X2MF1-M3	G

Note: Models with NPN NC output configurations are also available for all of the above models.

* Refer to Datasheet.

AC 2-Wire, Pre-wired Models

Appearance		Sensing distance	Model
			NO	NC
	M8	1.5 mm	E2E-X1R5Y1	E2E-X1R5Y2
	M12	2 mm	E2E-X2Y1 *1 *2	E2E-X2Y2
	M18	5 mm	E2E-X5Y1 *1 *2	E2E-X5Y2
	M30	10 mm	E2E-X10Y1 *1 *2	E2E-X10Y2
	M8	2 mm	E2E-X2MY1	E2E-X2MY2
	M12	5 mm	E2E-X5MY1 *1 *2	E2E-X5MY2
	M18	10 mm	E2E-X10MY1 *1	E2E-X10MY2
	M30	18 mm	E2E-X18MY1 *1	E2E-X18MY2

*1. Models with different frequencies are also available. The model numbers are E2E-X[]Y[]5 (example: E2E-X5Y15).

*2. Models are also available with 5-m cables. Add the cable length to the model number (example: E2E-X2Y1 5M).

AC 2-wire, Connector Models

Connector	Appearance		Sensing distance	Model
				NO	Applicable connector code *	NC	Applicable connector code *
M12		M12	2 mm	E2E-X2Y1-M1	E	E2E-X2Y2-M1	F
		M18	5 mm	E2E-X5Y1-M1	E	E2E-X5Y2-M1	F
		M30	10 mm	E2E-X10Y1-M1	E	E2E-X10Y2-M1	F
		M12	5 mm	E2E-X5MY1-M1	E	E2E-X5MY2-M1	F
		M18	10 mm	E2E-X10MY1-M1	E	E2E-X10MY2-M1	F
		M30	18 mm	E2E-X18MY1-M1	E	E2E-X18MY2-M1	F

* Refer to Datasheet.

AC/DC 2-Wire, Pre-wired Models

Appearance		Sensing distance	Operation mode	Model
	M12	3 mm	NO	E2E-X3T1
	M18	7 mm		E2E-X7T1 *
	M30	10 mm		E2E-X10T1

Note: These models do not conform to CE standards.

* Models are also available with 5-m cables. Add the cable length to the model number (example: E2E-X7T1 5M).